How to cook Homebrew Steroid Injections
If there is anything you wanna know , pls feel free to contact :
1. Email : jeana@yccreate.com
2. Skype ID : live:jeanayc
3. WhatsApp: +86 18126436945
I'm Jeana from China , serve you wholeheartedly.
Here is an example for 100mL test enanthate @250mg/mL
1. Email : jeana@yccreate.com
2. Skype ID : live:jeanayc
3. WhatsApp: +86 18126436945
I'm Jeana from China , serve you wholeheartedly.
Here is an example for 100mL test enanthate @250mg/mL
Recipe:
①25 grams of Test Enanthate powder =18.75mL
②2% BA =2mL
③20% BB =20mL
④GSO =51.25mL (Grapeseed oil or sesame oil, that's ok)
Here is a recipe for 250ml Test Enanthate @250mg/ml
Test Enanthate powder: 62.5g
Benzyl alcohol (BA): 5 ml(2%)
Benzyl benzoate (BB): 50 ml(20%)
Grapeseed oil: 148.13ml
Here are tools needed.
①Digital Scale (±0.1 or 0.01)
②Several samal piece of paper
③100mL Beaker and Glass Rod
④A frying Pan
⑤3mL syringe with 18-21 gauge needle
⑥20mL or 60 ml syringe with 18-21 gauge needle
⑦0.22μm Syringe Filter
⑧10 sets Vials @10mL/vial
(Note: A whole set include:vial; rubber stopper; cap)
⑨Hand Crimper
Making Injections steps:
Step (1) Weigh Test Enanthate Powder:
You have to do this very carefully. get your small piece of paper and place it on the scale then press tare to set it to zero so it doesn't weigh the paper. Then slowly add your powder.
Now here is the tricky part the powder weighs so little that the scale needs to be reset every time you add some. All you have to do is add some then press on the scale with your finger and let the number fall back down. Once you get 25 grams your good to go.
Step (2) Add powder,BA,BB into the beaker:
1.Dump the powder into your beaker;
2.Then Add 2mL of BA
3.Then add 20mL of BB
Step (3) Heating beaker in Water Bath (This Step is optional but it makes things easy)
1.Get a pot with a bout an inch of water in it and place it on the stove and set the eye to heat;
2.Put the beaker in the Pan,Pace the beaker into a few cm of water in a Pan or something similar;
3.Watch the powder,when it dissolved and the mixture get pretty close to clear
.
Once that's done, then we get the melted mixture.
Note: It is important not to use water that is too hot because this will cause some products to oxidize-150 f is a good temperature to use, alternatively boiled water from the kettle. The carrier oil should be the same temperature as the solution when it is added so if you warm the solution in a water bath you should also the same to the carrier oil.The objective at this point is simply to fully dissolved the powder into the solvents. There should be no "Hormone swirls" or any visible powder remaining in the solution and once this is achieved move on to the next step.
Step (4) Add Grape Seed Oil
Next wait the mixture cool down a little, then add your grape seed oil and let it all warm up again for a bit to make filtering a little bit faster.
Step (5) Filtering.
Draw up the solutions into the syringe you will be filtering with, this can be a single large syringe or this can be repeated multiple times with a smaller syringe. Remove the 0.22μm sterile syringe filter from it's packing and fix the green needle to the smaller side and then apply to the syringe.Wipe the top of the sterile vial with an Alcohol swab and insert the green needle in it, put the needle attached to the syringe filter into the vial as shown below:
Notes: The second needle equalizes the pressure as the solution enters the vial. Apply pressure to the syringe plunger to the filter the mixture. This is the most important part of this entire process as it is what sterilizes your product.
All finished steroids from any steroid lab must go through this very process.Occasionally one may find that the filter gets blocked or that the process slows drastically-it is acceptable to replace the filter with a new one if this occurs to save time. The time it takes to filter steroids depends on which steroid is being filtered and how much is being filtered, as well as the mg/ml of the product.Once the product is filtered in the sterile vial the process is complete.
Also you can use a syringe to draw out of the air from the Vials.
Step (6) Crimp them with flip off caps.
If there is anything you wanna know , pls feel free to contact :
1. Email : jeana@yccreate.com
2. Skype ID : live:jeanayc
3. WhatsApp:+86 18126436945
I'm Jeana from China , serve you wholeheartedly.
评论
发表评论